If a Star Configuration is Unavoidable > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

ISS has a Tricaster LiveText data integration solution for diving using ISS MMS competition management software. Confirm with your broadcaster that they are using LiveText 2.0 or higher for the Tricaster. There are modules for RS323-DCE (DB9F), RS232-DTE (DB9M), and RS485 interfaces. There are 6 uncommitted lines on the headers if you want to add additional signals to the ribbon cable. Although many applications use RS-485 signal levels, the speed, format, and protocol of the data transmission are not specified by RS-485. The data interface solution is owned by Integrated Sports Systems (ISS) Inc. and is licensed to Water Polo Canada. The solution contains a complete graphics package with your organization logo, watermark and event logo. The solution can be used for any Water Polo or FINA sanctioned competition. RS-485, like RS-422, can be made full-duplex by using four wires. RS-485, also known as TIA-485(-A) or EIA-485, is a standard, originally introduced in 1983, rs485 cable defining the electrical characteristics of drivers and receivers for use in serial communications systems. RS232 (serial) data feed from the ARES 21. Custom cable available upon request. If a star configuration is unavoidable, special RS-485 repeaters are available which bidirectionally listen for data on each span and then retransmit the data onto all other spans.

However the other standards that have been introduced more recently provide higher levels of performance that are very useful in may applications. It may be used to control video surveillance systems or to interconnect security control panels and devices such as access control card readers. These characteristics make RS-485 useful in industrial control systems and similar applications. RS-485 only specifies the electrical characteristics of the generator and the receiver: the physical layer. In a computer system, SCSI-2 and SCSI-3 may use this specification to implement the physical layer for data transmission between a controller and a disk drive. Multiple receivers may be connected to such a network in a linear, multidrop bus. RS-485 supports inexpensive local networks and multidrop communications links, using the same differential signaling over twisted pair as RS-422. The RS485 chip converts CMOS level transmit (Tx) and receive (Rx) lines to differential RS485 voltages than can be sent over long distances. This way, the lines will be biased to known voltages and nodes will not interpret the noise from undriven lines as actual data; without biasing resistors, the data lines float in such a way that electrical noise sensitivity is greatest when all device stations are silent or unpowered.

Under some conditions it can be used up to data transmission speeds of 64 Mbit/s. The diagram below shows potentials of the A (blue) and B (red) pins of an RS-485 line during transmission of one byte (0xD3, least significant bit first) of data using an asynchronous start-stop method. RS422 This standard gives a much higher data rate than RS232, but it uses differential transmission techniques. RS-485 standard conformant drivers provide a differential output of a minimum 1.5 V across a 54-Ω load, whereas standard conformant receivers detect a differential input down to 200 mV. The EIA has officially disbanded and the standard is now maintained by the TIA as TIA-485, but engineers and applications guides continue to use the RS-485 designation. The EIA once labeled all its standards with the prefix "RS" (Recommended Standard), but the EIA-TIA officially replaced "RS" with "EIA/TIA" to help identify the origin of its standards. Each of these standards meets a different requirement.

RS-422 and RS-485 Standards Overview and System Configurations, Application Report (pdf). It does not specify or recommend any communications protocol; Other standards define the protocols for communication over an RS-485 link. RS232 still being very widely used despite the fact that it has been in use for over 40 years. Many RS422 devices are compatible with RS232. Read more about RS232. Read more about RS485. Read more about RS422. However this contradicts the facts that an idle mark state is a logical one and the termination polarization puts B at a higher voltage in Profibus guidelines. TSB-89A, Application Guidelines for TIA/EIA-485-A does not recommend using star topology. Star and ring topologies are not recommended because of signal reflections or excessively low or high termination impedance. Termination resistors also reduce electrical noise sensitivity due to the lower impedance. This connection may be used to limit the common-mode signal that can be impressed on the receiver inputs.