You'll Never Guess This Replace Window Pane's Tricks > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can cause a lot of trouble. It could be a chance to upgrade your windows to energy efficient or insulated ones, and reap advantages like improved comfort, increased resale values and reduced utility costs.

It's a task you can take on yourself for less than the cost of hiring a professional. You'll only require the right tools and a few minutes of your time.

Glass

If your single pane windows are old, deteriorating or broken, replacing them with newer glass that is tempered or insulated can increase energy efficiency and reduce noise while preserving the historical integrity of older homes. The replacement of windows is easy and can be accomplished by homeowners with basic hand tools. In addition to a new pane, the following items are required such as latex glazing putty; Glazier's points; pliers and a heat gun for warming the old putty if required. Wear safety glasses and gloves before you begin. Working with broken glass could result in serious injuries.

Remove any broken glass pieces that remain. It is best to use pliers for this, but a flathead can work as well. Use a wood chisel, or putty knives to remove any old putty remaining around the frame and window sash. Be careful not to break the window sash. Be careful and slow. It is recommended to do this on a sturdy ladder instead of the ground and place someone on the sash in order to help hold it in place.

Make sure the window frame is ready to accept the new pane when you have removed the old putty. Take measurements of the width and height of the opening for the sash and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to an hardware or home centers store to have an item cut from glass that is in stock to the correct size. You can also cut the glass yourself if have the tools you need.

After installing the new glass, apply a small amount of caulking on the edges. This will make the glass weatherproof. Then install a glazier's point on the frame's opposite side to hold the pane in place. The points shouldn't be too tight that they cause friction between the frame and the sash, but they should also not be loose.

Before applying the putty on the surface, gently knead it until it is smooth and free from lumps. Then you can roll it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's points are small triangular metal pieces that allow glass to be secured to the frame without causing damage to the delicate surface. It's easy to learn how to use this hidden tool, and you'll be able to save money on the expense of a professional installation.

After the old putty as well as the glazier's points have been removed and the frame is thoroughly cleaned with a knife to eliminate any remaining traces. Lightly sand the wood in the rabbet grooves if needed to smooth rough areas. If you decide to sand the wood, make sure to protect it with painter's tape to avoid accidental damage.

Write down the exact dimensions of the frame. Take these measurements to a hardware store or a home center and request that the new pane cut slightly smaller than the frame's opening. This will ensure a snug fit and will allow room for expansion and contraction.

Place the new pane into the frame and push it in place by using your hands. Then, use the tip of your chisel, or the back of the putty knife to tap in the glazier's facets, as shown in Figure 11. When you're done, they should be flush with the top edge of the pane and the shoulders that are raised of the points should be below the rabbet's lip. groove.

Apply a thin layer of glazing compound to the rabbet grooves as well as the edges of the new glass. This will seal and protect the edges. Allow it to dry and cure completely.

Install the new window sash once the glazing compound has dried. First, coat the wood with a heavy coat of linseed oil. This will stop the new putty from drying out and cracking due to the moisture it absorbs. Apply this coat using a brush or the tip of your knife, then use the chisel, or the back end from the putty knife to gently hammer the new sash and glazier's points into the rabbet grooves. Repeat this process at intervals of 10 inches around the frame.

Putty

A baseball thrown, a rock thrown in error or a branch falling can result in a cracked or cracked window. Fortunately, the majority of windows replacement can be replaced by simply putting a new piece in place. The glass is held in place by small clips made of metal called the glazier's pointed and putty, which is often called glazing compound. Remove the old pane and replace window pane clean the area with the rag, a pull-type scraper, or a wood chisel. Wear safety glasses and gloves while working. If the window is secured to the frame, you'll have to employ a heat gun in order to soften the adhesive before prying it free.

If you are planning to replace window pane (Visit Home Page) the original sash, gently remove the molding pieces that hold the old pane in place. Sand the sash until it's flat and ready to receive new caulk. Once the sash is installed and sanded, apply a fresh caulk made of silicone around the glass to ensure that it won't leak or discolor over time.

Take out the glazing points in the rabbets. These are the grooves in the sash, where the glass is located. If they're difficult to cut out, try holding an instrument like a heat gun over them to soften them up first. If you're using a heated gun, make sure not to scratch the railings or sash by holding the tool too closely.

Make the bed for your new pane by removing the old glaze points and putty. Roll a rope with glazing compound between your fingers and make it about 1/2 inch thick. Press it into the rabbets where the glass will be put. It's important that the glass sits on the putty on both sides, so if you need to do so, gently tap the glass into the rabbet using your thumb.

If the new pane has damaged, you can use a silicone caulk or glass glue that is based on solvents to fill in the crack before pressing it into the sash. If the crack is not sealed, you'll require putty to keep the water out. Once the putty is dry clean the oily film off of the glass and let it dry completely before painting. Paint before the putty has dried completely. It will not make a strong seal and could be leaking or discoloring over time.

Paint

If you've suffered a break in a window pane, you might be concerned about the expense of a new one. However, replacing a single glass pane doesn't require a huge amount of money if you do it yourself. In fact, even a double-pane window can be replaced at only a fraction of the cost of an expert.

If you are working on a large window, ensure that it is securely fixed to the frame. This task can be made relatively simple and quick with the right tools and techniques.

When you're ready to start taking off the old window pane by prying out the glazing points made of metal that are attached to it. These are tiny triangles of metal that act as "nails" that hold the window within the frame. They are buried under a bead of glazing putty, which is then cured to form a solid, formed wedge that holds the window firmly in place and conceals the window's points.

After removing the old pane, clean the frame and wood. Scrape away any old paint and sand down the rabbet grooves where the glazing points used to be. These should be sanded to bare wood, to allow you to paint them the same shade as the rest of the frame. After sanding the wood then apply a layer of flax oil. This will help prolong the life of the frame.

Then, you need to measure the size of the window's opening. You will need to take horizontal and vertical measurements of the entire opening, as well as the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will also allow for expansion and contraction of the glass during seasonal change. Take these dimensions to your local hardware or home improvement store, and they will have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.