Seven Explanations On Why Replace Window Pane Is Important > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is an issue. It can also be an opportunity to upgrade your glass to energy-efficient or insulated windows, and reap benefits like improved comfort, increased the value of resales and lower utility bills.

You can do it yourself at a fraction of what it would cost to hire an expert. You only need the appropriate tools and a few minutes of your time.

Glass

If your single-pane windows are old, deteriorating or broken replacing them with modern insulated or tempered glass can improve energy efficiency and reduce noise while also preserving the historical integrity of older homes. A majority of homeowners with hand tools can repair a window pane. You'll also require a replacement window pane, glazier's tips, pliers, and latex glaze putty. If needed, you can make use of a heat gun to warm the old putty. Wear safety glasses and gloves prior to starting. Working with broken glass could cause serious injuries.

Begin by removing any remaining broken pieces of glass. This is best done using a pair of pliers, but a flathead screwdriver may be effective in a pinch. Use a wood chisel, or putty knives, to take away any remaining old putty around the frame and the window sash. Work slowly and carefully making sure not to break the existing window sash. It is a good idea to work using a sturdy ladder rather than the ground and to have someone stand below the sash to help keep it in place.

After you've removed all the old putty, it is time to prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of width and height. These measurements can be sent to a hardware or home center store to have cut a piece of stock glass to the right size. You can cut the glass yourself if you possess the right tools.

After putting in the new pane After installing the new pane, apply a small amount of caulking around the edge to ensure it is weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points shouldn't be too tight that they cause friction between the frame and sash However, they should not be loose.

Before putting the putty on, knead it thoroughly until it is soft and free of lumps. Cut it into pencil-sized pieces. Place the first strip to the corner of the frame, working from one corner to the other so that it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular pieces of steel which help to secure the glass to the frame without causing damage to the delicate surface. Understanding how to use these tiny pieces of help is simple and can save you money on a professional installation or the cost of new glass.

After the old putty as well as glazier's points are removed and the frame is thoroughly cleaned using a utility knife to remove any remaining traces. Lightly sand the frame in the rabbet grooves if needed to smooth out rough areas. If you do sand your wood, ensure you protect it with painter's tack to avoid accidental damage.

Note down the exact dimensions of the frame. Take these measurements to a hardware store or a home center and request that the new pane cut smaller than the frame's opening. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Insert the new pane into the frame and press it down with your hands. Use the chisel's point or the edge of the putty blade to tap the glaziers' points as illustrated in Figure 11. The glazier's points should be in line with the top edge of your pane and the raised shoulders should be just below the lip.

Apply a thin layer of glazing compound to the rabbet grooves and the edges of the new glass. This will protect and seal the edges. Allow it to dry and cure completely.

After the glazing compound dries it's time to put in the new window sash. The first step is to coat the wood with a thick layer of linseed. This will stop the new putty from drying out or cracking due to the moisture it absorbs. Apply the coating using a brush this coat, or the tip of the putty blade. Then, use the chisel that is on the back of the tool or the back of the handle to gently hit the new sash, or glazier's tip into the rabbet grooves. Repeat this process in intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown by error, or a tree falling could result in a broken or cracked window pane. Most windows can be replaced easily by putting in a new piece. The glass is held in place by tiny metal clips known as a glazier's point, and putty, also called glazing compound. Before you install a new pane, first remove the old one and clean up the area using the help of a rag, the pull-type paint scraper or a wood chisel. Wear protective glasses and gloves while working. You'll require a heat gun when the window is fixed into the frame.

If you are planning to replace the original sash, remove any molding pieces that secure the old pane. Sand the sash until it is flat and ready to receive new caulk. After the sash has been installed then, you can apply a silicone caulk over the glass. This will ensure that it doesn't get soiled or discolor over time.

Remove the glazing points from the rabbets, or the grooves in the sash that the glass sits. If they're hard to chisel, use the hand tool, such as a heatgun over them to soften first. When using a heat tool, make sure to not scratch the sash or its railings.

Once the old glaze points and putty have been removed, prepare a bed for the new pane. Roll a rope with glazing compound between your fingers, and then make it about 1/2 inch thick. Then, push it into the rabbets in which the glass will be. The glass must be positioned against the putty on both sides. If needed you want to tap your glass lightly into the rabbet with your thumb.

If the new pane is cracked, you can apply the silicone caulk or glass glue based on solvents to seal the crack before pressing it into the sash. Otherwise, you'll need to apply putty on the crack to create an airtight seal and keep water out. After the putty has dried remove the oily film off the glass and let it dry completely before you paint. If you paint before the putty has completely dry, it won't form a solid seal and could discolor or leak over time.

Paint

If you've experienced a broken window pane, you might be worried about the expense of a new one. In reality, replacing a single piece of glass doesn't need to be expensive if you do it on your own. In fact, even a double-pane window can be replaced for Glaziers less than the cost of a professional.

If you're working with a large glass window first, ensure that it is securely fixed to the frame. This job can be made relatively simple and quick with the proper tools and techniques.

If you're ready to begin, begin by removing the old window glass replacement by removing the glazing points made of metal that are attached to it. These are basically small metal triangles which function as "nails" that keep the window in place within the frame of wood. They are placed under a bead or glazing glue which hardens into a solid wedge that holds the wood frame securely in place and hides the sharp edges.

After taking off the old pane clean the frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points were. They should be sanded to bare wood, to allow you to paint them the same color as the rest of the frame. After sanding, apply a layer of flax oil on the wood that is not sanded down to help extend its lifespan.

Next, measure the dimensions of the window's opening. You will need to measure the horizontal and vertical dimensions of the entire opening as well as the thickness. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will allow for seasonal changes in the glass. Bring these measurements to the hardware or home improvement store, and they will have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.